JCB 550-170 LOAD CONTROL (SUPPLEMENT) Service Repair Manual

Please download to get full document.

View again

of 17
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Similar Documents
Information Report
Category:

Automotive

Published:

Views: 0 | Pages: 17

Extension: PDF | Download: 0

Share
Description
This is the Highly Detailed factory service repair manual for theJCB 550-170 LOAD CONTROL, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.JCB 550-170 LOAD CONTROL Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly. Service Repair Manual Covers: Introduction About This Supplement About the Load Control Systems Identification Care and Safety LCS (Six Valve Manifold) Introduction Circuit Description Hydraulics Schematic Electrical Schematic Harness Data Logic Sequence Calibration LC1 and LC4 (540-170 Only) Introduction Circuit Description Hydraulics Schematic Harness Data Logic Sequence Installation Calibration LC2 and LC3 Introduction Circuit Description - 528-70 Circuit Description - 535-95, 531-70, 536-70 and 541-70 Circuit Description - 533-105 and 540-140 Circuit Description - 535-125 HiViz and 535-140 HiViz Hydraulics Schematic Harness Data Logic Sequence (All LC2/LC3 Systems) Calibration LC5 Introduction Circuit Description Hydraulics Schematic Harness Data Logic Sequence Calibration MC05 Introduction Circuit Description Hydraulics Schematic Harness Data Electrical Schematics Logic Sequence Calibration MC06 Introduction Circuit Descriptions - Parallel Machines Circuit Description - LSP + Gearpump Machines Circuit Description - LSP + Variflow Machines Hydraulics Schematics Harness Data Electrical Schematics Logic Sequence Calibration Fault Finding All Load Control Systems Testing and Adjustment Testing Adjustment File Format: PDF Compatible: All Versions of Windows & Mac Language: English Requirements: Adobe PDF Reader NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveJCB 550-170 LOAD CONTROL Service Repair Workshop Manual. Looking for some other Service Repair Manual,please check: https://www.aservicemanualpdf.com/ Thanks for visiting!
Transcript
  • 1. Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means, electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE. World Class Customer Support 9803/3665-3 Publication No. Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400 Service Manual Load Control (Supplement) K Introduction ( T 1) K LCS (Six Valve Manifold) ( T 9) K LC1 and LC4 (540-170 Only) ( T 37) K LC2 and LC3 ( T 67) K LC5 ( T 151) K MC05 ( T 187) K MC06 ( T 217) K Fault Finding ( T 321) K Testing and Adjustment ( T 329)
  • 2. Page No.Contents i i Introduction About This Supplement .................................................................................1 About the Load Control Systems ...................................................................2 Identification ..................................................................................................3 Care and Safety ............................................................................................7 LCS (Six Valve Manifold) Introduction ....................................................................................................9 Circuit Description ....................................................................................... 11 Hydraulics Schematic ..................................................................................20 Electrical Schematic ....................................................................................22 Harness Data ...............................................................................................24 Logic Sequence ...........................................................................................28 Calibration ...................................................................................................31 LC1 and LC4 (540-170 Only) Introduction ..................................................................................................37 Circuit Description .......................................................................................39 Hydraulics Schematic ..................................................................................47 Harness Data ...............................................................................................50 Logic Sequence ...........................................................................................54 Installation ...................................................................................................56 Calibration ...................................................................................................62 LC2 and LC3 Introduction ..................................................................................................67 Circuit Description - 528-70 .........................................................................69 Circuit Description - 535-95, 531-70, 536-70 and 541-70 ...........................75 Circuit Description - 533-105 and 540-140 ..................................................86 Circuit Description - 535-125 HiViz and 535-140 HiViz ...............................99 Hydraulics Schematic ................................................................................109 Harness Data ............................................................................................. 114 Logic Sequence (All LC2/LC3 Systems) ...................................................131 Calibration .................................................................................................133 LC5 Introduction ................................................................................................151 Circuit Description .....................................................................................153 Hydraulics Schematic ................................................................................169 Harness Data .............................................................................................172 Logic Sequence .........................................................................................178 Calibration .................................................................................................180 MC05 Introduction ................................................................................................187 Circuit Description .....................................................................................189 Hydraulics Schematic ................................................................................201 Harness Data .............................................................................................204 Electrical Schematics ................................................................................209 Logic Sequence ......................................................................................... 211 Calibration .................................................................................................213 MC06 Introduction ................................................................................................217 Circuit Descriptions - Parallel Machines ....................................................219
  • 3. Page No.Contents ii ii Circuit Description - LSP + Gearpump Machines ......................................235 Circuit Description - LSP + Variflow Machines ..........................................250 Hydraulics Schematics ..............................................................................265 Harness Data .............................................................................................277 Electrical Schematics ................................................................................300 Logic Sequence .........................................................................................305 Calibration .................................................................................................307 Fault Finding All Load Control Systems ..........................................................................321 Testing and Adjustment Testing .......................................................................................................329 Adjustment ................................................................................................340
  • 4. 1 19803/3665-3 Introduction About This Supplement Machine Model and Serial Number This publication provides information for the following Load Control Systems: – LCS (Six Valve Manifold) Load Control System – LC1/LC4 Load Control System – LC2/LC3 Load Control System – LC5 Load Control System – MC05 Load Control System – MC06 Load Control System See the appropriate system topic for machine serial nos., where relevant. Using the Service Manual Supplement This manual is a supplement to the JCB Loadall Service Manual. The information covers the JCB Loadall machines fitted with the Load Control System. Each variant of Load Control System (see opposite) is dealt with separately, each having its own topic in this Supplement. Only those areas of the machine which are different from the standard Loadall are dealt with here. For all other information refer to the appropriate Loadall Service Manual. Unless specified otherwise, all references to `Service Manual' in this supplement are to be taken as meaning the Service Manual specific to the standard machine. Read the standard Service Manual and this supplement completely and carefully to familiarise yourself with the machine before carrying out any servicing procedures. Units of Measurement T1-001_2 In this publication, the S.I. system of units is used. For example, liquid capacities are given in litres. The Imperial units follow in parentheses ( ) eg 28 litres (6 gal). Cross References T1-004_2 In this publication, page cross references are made by presenting the subject title printed in bold, italic and underlined. It is preceeded by the 'go to' symbol. The number of the page upon which the subject begins, is indicated within the brackets. For example: K Cross References ( T 1).
  • 5. Introduction About the Load Control Systems 2 29803/3665-3 About the Load Control Systems General Information A Load Control System (LCS) is an enhancement to the devices that JCB currently fit as standard, i.e. loadcharts, boom extension markers and Load Moment Indicator (LMI). These are still the primary source of information to allow the operator to operate the machine correctly. The Load Control System offers additional control if the operator makes an inadvertent movement of the load. The system must not be relied upon as the primary source of protection for the machine. The duty of care is still with the operator/site agent to: – know the mass and load centre of loads being handled. – know boom angle and extension that will be required to place the load (this can be checked by doing a dry run first without the load) – whilst moving the load, obey LMI indications, lift charts and boom extension markers. Note: Note: The LCS provides a degree of protection only against the machine tipping forward. It does not protect against tipping sideways or rearwards, nor tipping due to the machine being used on unsuitable ground nor operator mishandling (sharp direction changes, etc.). Neither will the system protect against instability due to the stabiliser legs being lifted nor misuse of the chassis levelling (sway) function (if either of these options are fitted).
  • 6. Introduction Identification 3 39803/3665-3 Identification There are many variants of the Load Control System. Although they all have a common purpose - to help prevent the load moving into a position which would make the machine unstable - there are variations in the way this is achieved on different Loadall models. Also, some variants of the system incorporate additional features such as stabiliser isolation and load retrieval. The following table will help you identify which variant may be installed on any particular model of Loadall. Note: For 536-60, 536-70, 531-70, 535-95 and 541-70 machines, you will need also to refer to the table of Hydraulic System Variants. K Table 2. Identification of Hydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) ( T 5) Table 1. System Applicability, Identifying Features and Territorial Availability Territories 540-170 540-140 537-135 535-140Hi-Viz 535-140 535-125Hi-Viz 535-125 535-95 533-105 532-120 541-70 536-70 531-70 536-60 528-70 System Description and Identifying Features Visual Identifier France LCS Original system (now obsolete). Identifying features: large 6-valve manifold mounted on the chassis side plate and twin aperture LMI. Rest of the World (ROW) (not Australia/New Zealand) LC2 2 stage cut -out system. Identifying features: Additional switch in cab for Load Control selection. Load Control Valve inserted between pump and valve block and single aperture LMI with 4 way and 6 way connectors. ROW (not Australia/New Zealand) LC3 As LC2 + stabiliser isolation. Identifying features: as LC2, plus stabilisers isolate at 10° boom angle.
  • 7. Introduction Identification 4 49803/3665-3 ROW (not Australia/New Zealand) LC5 2 stage cut -out system + lift & retract to retrieve load. Identifying features: Additional switch in cab for Load Control selection. Load Control Valve inserted between pump and valve block, single aperture LMI with 4 way and 6 way connectors and switches on the valve block. ROW (not Australia/New Zealand) LC1 540-170 system. Identifyingfeatures:twin LMI aperture with 4 way & 6 way connectors. ROW (not Australia/New Zealand) LC4 As LC1+ stabiliser isolation. Identifying features: as LC1, plus stabilisers isolate at 10° boom angle. Australia/New Zealand MCO5 As LC1 + AS1418.19. Identifyingfeatures:twin aperture LMI with 4 way & 8 way connectors. Australia/New Zealand MCO6 2 stage cut-out system + lift & retract to retrieve load + AS1418.19. Identifying features: Additional switch in cab for Load Control selection. Boom back switch, single aperture LMI with 4 way & 6 way connectors. Territories 540-170 540-140 537-135 535-140Hi-Viz 535-140 535-125Hi-Viz 535-125 535-95 533-105 532-120 541-70 536-70 531-70 536-60 528-70 System Description and Identifying Features Visual Identifier
  • 8. Introduction Identification 5 59803/3665-3 Hydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) The hydraulic circuit of the 536-60, 536-70, 535-95, 531-70 and 541-70 machines may be one of a number of variants. Each variant requires a slightly different Load Control System. If you are working with one of these machines it is important that you know which type of hydraulic system is installed, to ensure that you refer to the correct hydraulic and electrical diagrams in this supplement. The following table shows the easily identifiable differences between hydraulic systems. Table 2. Identification of Hydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) System Type Main Pump Type Control Lever Type Parallel System Fixed flow double or triple gear pump. Parallel control valve (black) with four manual spools. Separate control levers for boom and auxiliary services. Fixed flow double or triple gear pump. Parallel control valve (black) with two electro servo and two manual spools. Cab mounted control lever with push button controls. Fixed flow double gear pump. Parallel control valve (black) with two integrated electro servo spools and two manual spools. Cab mounted control lever with thumbwheel controls. Hydraulic services are controlled by a machine control ECU with electronic flowshare feature.
  • 9. Introduction Identification 6 69803/3665-3 LSP Gearpump System Fixed flow triple gear pump. Flowshare control valve (blue) with two proportional electro servo and two manual spools. Cab mounted control lever with thumb wheel controls. LSP Variflow System Variable flow pump with one fixed flow gearpump for cooling fan, sway and servo oil supply. Flowshare control valve (blue) with two electro servo and two manual spools. Cab mounted control lever with thumbwheel controls. Variable flow pump with one fixed flow gearpump for cooling fan, sway and servo oil supply. Flowshare control valve (blue) with four integrated electro servo spools. Seat pod mounted control lever with thumbwheel controls System Type Main Pump Type Control Lever Type
  • 10. Introduction Care and Safety 7 79803/3665-3 Care and Safety Safety Notices In this publication and on the machine, there are safety notices. Each notice starts with a signal word. The signal word meanings are given below. !MDANGER Denotes an extreme hazard exists. If proper precautions are not taken, it is highly probable that the operator (or others) could be killed or seriously injured. INT-1-2-1 !MWARNING Denotes a hazard exists. If proper precautions are not taken, the operator (or others) could be killed or seriously injured. INT-1-2-2 !MCAUTION Denotes a reminder of safety practices. Failure to follow these safety practices could result in injury to the operator (or others) and possible damage to the machine. INT-1-2-3 General Safety !MDANGER Study this Supplement and the Service Manual for the machine before carrying out any maintenance work on the machine. You must always understand and observe the relevant laws and regulations. If you are unsure about anything, ask your JCB Distributor. INT-1-2-6
  • 11. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 12. 9 99803/3665-3 LCS (Six Valve Manifold) Introduction Machine Model and Serial Number The LCS Load Control System (LCS) is compatible with following models in the JCB Loadall machine range: – 528-70 Up to SN 797511 – 532-120 Up to SN 1064455 – 533-105 Up to SN 1064702 – 535-95 Up to SN 1064715 – 537-135 Up to SN1064473 General Description When the LCS is selected, it reduces the risk of tipping forward when the machine reaches a predetermined point near to its maximum working limit. This is achieved by stopping boom lower, boom extend, dump and crowd functions, in order to prevent further movement of a load past the predetermined point. Boom lift and boom retract functions are allowed in order to retrieve the load from a point of cutout. The system has two working modes, Load Control Mode and Ground Work Mode. Load Control Mode is automatically entered when the machine is started. Note: The LCS provides a degree of protection only against the machine tipping forward. It does not protect against tipping sideways or rearwards, nor tipping due to the machine being used on unsuitable ground nor operator mishandling (sharp direction changes, etc.). Neither will the system protect against instability due to the stabiliser legs being lifted nor misuse of the chassis levelling (sway) function (if either of these options are fitted). The stabilisers and/or chassis levelling rams are not interlocked into the LCS. In Load Control mode, the boom lower hydraulic supply is progressively reduced (derated) as the weight on the rear axle becomes less, ensuring that the load movement is stopped smoothly and without jerking. The tilt hydraulic flow is also restricted; this restriction is constant throughout the range. The extend function operates as normal until the limit is reached. It is, therefore, a characteristic of the system that lowering and tilt movements are slightly slower than when Ground Work mode is selected. This is normal and does not indicate a machine fault. Once the limit is reached, any movement of the load which would further reduce the stability of the machine is prevented. This means that extend, lower, crowd and dump functions are all disabled. In Ground Work mode, the system functions as the standard LMI. Testing procedures described in this manual should be carried out on level ground with the road wheels in the straight ahead position.
  • 13. LCS (Six Valve Manifold) Introduction 10 109803/3665-3 The LCS Indicator Display Fig 1. A Green LEDs (3) Safe when lit B Amber LED Caution when lit - approaching machine stability limits C Red LED Danger when lit - machine at limit of stability D Power ON indicator E Display button F Mode change button G Load Control mode symbol Lit when Load Control mode selected, flashes when red LED C is lit (in Load Control mode) H Ground Work mode symbol Lit when Ground Work mode selected
  • 14. LCS (Six Valve Manifold) Circuit Description 11 119803/3665-3 Circuit Description Introduction Fig 2. Typical Circuit The following description, outlines the operation of the LCS as fitted to Series I machines fitted with stabilisers (532-120, 533-105 and 537-135). It should be read with reference to the following: K Hydraulics Schematic ( T 20) K Electrical Schematic ( T 22) K Logic Sequence ( T 28) In non-stabilised machines (528-70, 535-95), valve C (lift circuit control valve) is not fitted and references to valve C should be ignored. The lift service operates normally. Interface with Standard Hydraulic System Load Control functions are controlled by the six valve manifold AA, which is inserted in the hydraulic circuit between the main control valve block and the service rams. Refer to: K Component Key ( T 12) K Fig 2. ( T 11) K Fig 3. ( T 13)
  • 15. LCS (Six Valve Manifold) Circuit Description 12 129803/3665-3 Component Key K Fig 2. ( T 11) and K Fig 3. ( T 13) Note: Valves B, C and D are fitted with manual overrides. Note: All valves are shown in the de-energised position. Note: Valve C and associated components shown th
  • We Need Your Support
    Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

    Thanks to everyone for your continued support.

    No, Thanks
    SAVE OUR EARTH

    We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

    More details...

    Sign Now!

    We are very appreciated for your Prompt Action!

    x